A design to break out the dual micro HDMI ports out to a panel adjacent to the USB/Ethernet ports.
All traces are length matched on high speed differential signals.
This design has not been tested yet, it is currently in production (04/2020)
This has been deisgned to use the BossCon HDD-M-CN09 micro HDMI board edge connectors. Other types will not fit as they all have slightly varying pin spac...
This is a Raspberry Pi Zero W hat/shield with USB MIDI input, stereo audio output, 3 user-configurable buttons and OLED display.
To use as an audio card, enable PWM audio output by adding `dtoverlay=pwm-2chan,pin=18,func=2,pin2=13,func2=4` at the end of *config.txt* file.
Remeber that HDMI audio output is the default; use `raspi-config` to force output to 3.5mm audio jack.
If you can't find 47uF...
# DC to DC power #
With following functionalities:
- Power a Raspberry PI with 2S-6S accumulator
- Fixations for a FPV emitter.
- Connexions from Raspberry-PI to FPV emitter
- Can also power a radio control receiver with several servos.
This schematic has a few functions to this circuit. This circuit takes voltages starting from 4V to a max. of 13V. It was an open source project I found online. I've redone this board's schematic. But when it came to de PCB design I kinda lost it. I got as close to sorting the components on the board, but I didn't know where to start connecting wires or how. I'm taking a little break, but if anyon...
Raspberry Pi Zero hat/shield with MIDI input, stereo audio output, 3 buttons and OLED display.
OBSOLETE: this version is obsolete. Check new version without the MIDI port, but with improved audio and cleaner schematic https://easyeda.com/account/project?project=2bca68b51d954e19b68cba485984fb42
Template (PCB and interface symbol) to copy for any kind of HAT designs for Raspberry Pi B+. The PCB contains 6 layers with layer display at the lower edge. The assignment of layers is:
- top: signal, polygon connected to GND
- bottom: signal, polygon connected to GND
- layer 1: inner, signal
- layer 2: inner, polygon VCC
- layer 3: inner, polygon GND
- layer 4: inner, signal
Note: geometry tes...
Latching Mosfet switch
Based on work at:
R8 allows a shorter wait period on switch hold / raspi gpio driven low
or a 3.3v Zener diode can/should be used to protect GPIO pin
Mosfets are separate devices
In PCB V1 the P-Channel device is TO-220 while the N-Channel is DPAK
Handheld Retropie gaming console based on CM3+ and DPI screen.
HAT or pHAT for Raspberry Pi. Designed with the Pi Zero W in mind, so it shares the footprint of the Zero.
HAT has an ATmega328PB connected via I2C, SPI and UART,allowing both flashing, and many forms of communication.
Included a space for a Mini DC-DC voltage regulator. These are good for 3A of power, but make sure to solder the 5V pads and cut the ADJ pad lead.
Headers for SPI(ICSP) and both...
# Shield fo Raspberry PI zero W. #
# Introduction #
This shield created for moving many digital servos as [LOBOT LX-16A or LOBOT LX15D](www.lobot-robot.com).
# Desing #
This shield included microcontroller stm32f413 and st-link scheme on stm32f103 base. Stm32f413 connected to raspberry connector via SPI, UART and I2C interfaces. You can to use stm32f413 as:
- USB/UART bridge for raspberry cons...
Our website uses essential cookies to help us ensure that it is working as expected, and uses optional analytics cookies to offer you a better browsing experience. To find out more, read our Cookie Notice