TinyCalibrator is an oscillator calibrator and high-voltage fuse resetter for 8-pin ATtinys based on an ATtiny44/84. Because the 8-pin ATtinys only have a few GPIO pins available, they are usually operated without an external clock. The internal oscillator does a good job in most applications, but when it comes to precise timing, its +/-10% accuracy is often insufficient. Fortunately, t...
TinyRemoteRF is an RF remote control based on an ATtiny13A microcontroller and a SYN115 ASK transmitter IC powered by a CR2032 coin cell battery.
- Firmware (Github): https://github.com/wagiminator/ATtiny13-TinyRemoteRF
The wiring is shown below:
TinyHVSP is a stand-alone high-voltage serial programmer and fuse resetter for ATtiny 13/25/45/85. This project was superseded by the more versatile [TinyCalibrator](https://github.com/wagiminator/ATtiny84-TinyCalibrator).
- Project Video (YouTube): https://youtu.be/2Q7D2RwkOMg
- Firmware (Github): https://github.com/wagiminator/ATtiny84-TinyHVSP
TinyRemote is a 5-button IR remote control based on an ATtiny13A powered by a CR2032 or LIR2032 coin cell battery.
- Project Video (YouTube): https://youtu.be/ad3eyNCov9c
- Firmware (Github): https://github.com/wagiminator/ATtiny13-TinyRemote
For the 12-button versi...
TinyCandle is a simple tealight candle simulation based on the ATtiny13A.
- Firmware (Github): https://github.com/wagiminator/ATtiny13-TinyCandle
## Candle Simulation
The simulation code is based on the great work of [Mark Sherman](https://gith...
# TinyICOC - AVR In-Circuit Oscillator Calibrator
Sometimes AVRs are operated without an external clock. The internal oscillator does a good job in most applications, but when it comes to precise timing, its +/-10% accuracy is often insufficient. Fortunately, the oscillator can be calibrated, increasing its accuracy to +/-2% or better. There are a few ways to perform this manual calibration, but s...
The device is an addition to the gas handle of the electric bike, simulating the operation of the controller in the current control mode. Smooth start after a long standing on the spot and at the same time a quick set of turns after a short-term gas release and subsequent increase. The signal level is reset instantly, and the rise depending on the previous state in time. Does not require a real m...
This is a charlieplexing PCB. The figure is a black cat sitting on an unicorn ([on reddit](https://www.reddit.com/r/blackcats/comments/7opy9u/and_lo_i_saw_a_rider_on_a_pale_horse_and_the/)). The artwork was made by inkscape and EasyEDA.
A Tinkercad simulation with arduino compatible spaghetti code:
TinyRemoteXL is a 12-button IR remote control based on an ATtiny13A powered by a CR2032 or LIR2032 coin cell battery.
- Firmware (Github): https://github.com/wagiminator/ATtiny13-TinyRemoteXL
TinyPlayer is an IR remote controlled and LiPo battery powered MP3 player based on ATtiny13A and DFPlayerMini module. The DFPlayer module is controlled via a simple cycle-precise software implementation of the UART protocol (8N1, 9600 BAUD) in half-duplex mode. The volume last set as well as the track number last played are saved in the EEPROM and automatically loaded the next time it i...
This is little board I made to help me with ATTINY chips projects.
It has 6 pin USBASP input and 4 pin headers for each of the pin of the chip times 3, which makes it easy to connect oscilloscope and put it on breadboard in same time and still have pins to connect to it external device. Also it has both SOIC8 and DIP8 packages support.
Tiny little helper.
Простой электронный ключ на ATTINY13, с питанием по USB (от компьютера, ноутбука, зарядного утройства или повер-банка в полевых условиях).
Уменьшенный вариант - https://easyeda.com/UN7FGO/USB_CW_KEY
Скетч для среды Ардуино, можно взять здесь - https://github.com/UN7FGO/USB_CW_KEY
Выход на трансивер коммутируется на "общий провод" транзистором.
Есть возможность звукового самоконтроля, который о...
Our website uses essential cookies to help us ensure that it is working as expected, and uses optional analytics cookies to offer you a better browsing experience. To find out more, read our Cookie Notice